Proto-Board® Design Workstation Series &
Powered Proto-Boards

Features:

• Removable breadboard area with lifetime warranty
• 1MHz multi-waveform function generator
• Quad voltage power supply
• Logic probe with pulse capture
• Square wave pulse generator
• BCD to 7-segment decoder/display
• 8-channel logic indicators
• DC digital voltmeter with four ranges
• Two open collector output pulsers
• 8 selectable logic switches
• Detachable 25-way computer interface

Specifications:

• Power: 3-wire AC line input (110V 50-60Hz typical) with power indicator
• Power Supplies:
  • +5VDC @ 1.0A, ripple <5mV
  • +V Variable DC O/P: +1.3V to +15V (150mA @ 1.3V, 500mA @ +15V max), ripple <5mV
  • -V Variable DC O/P -1.3V to -15V (150mA @ -1.3V, 500mA @ -15V max), ripple <5mV
  • Fixed AC output: 12.6 VAC center tapped @ 100mA max
• Function Generator
  • Frequency range: 0.1Hz to 1MHz in seven ranges
  • Output voltage: 0 to +10V (20V p-p), short circuit protected
  • Output waveforms: Sine, square, triangle, TTL
  • Sine wave: Distortion <3% (10Hz to 100kHz)
  • TTL pulse: Rise and fall time <25ns; Drive 10 TTL loads
  • Square wave: Rise and fall time <0.5µs
• Logic Indicators: 16 LED's 8 red to indicate logic high, 8 green to indicate a logic low
• Logic Probe: Built-in TTL/CMOS compatible logic probe. Captures fast single shot events and pulse trains. Input impedance 300kΩ overload protection +50VDC, min. detectable pulse width 200nsec. TTL threshold low +0.8V high +2.25V, CMOS threshold low +30%Vcc high +70%Vcc. Memory mode, latches on first transition and LED remains on until probe is reset.
  • Tie Points: Sine, Square, Triangle, Wave: 10, TTO: 10
• Debounced Pushbuttons (Pulser): Two push-button operated, open-collector output pulsers, each with one normally-open and one normally-closed output. Each output can sink up to 25mA.
• Potentiometers: One 1kΩ, one 10kΩ, all leads available and uncommitted
  • Tie Points: 20 per wiper: 10 per remaining contact
• Pulse Generators: A nominal square wave source with 6 ranges covering from 1Hz to 1MHz. Two switch selectable output ranges, one (TTL) or 5Vp-p and one (CMOS) linked to the variable supply voltage and capable of giving any voltage from 0V to 18Vp-p. Ten tie points are provided to connect to external circuits.
• Digital Voltmeter: A switch selectable DC digital voltmeter with four ranges: +/-000.0-199.9mV,+/-0.200-1.999V, +/-2.00-19.99V and +/-20.0-199.9V. The input is protected against excess voltages to +/-300V ICD Readout.
• BNC Connector: One BNC connectors, shell connected to ground
  • Tie Points: 1 x 0.6mm socket per input; 1 x 0.6mm socket for 0V
• Spot Switches: 2 SPDT slide switches, all leads available and uncommitted
  • Tie Points: 10 per wiper, 5 per remaining contact
• Logic Switches: 8 Logic switches select logic low or logic high, low level is ground. High level is switchable between the fixed +5V supply and the +1.3 through +15V supply
• Tie Points: 5 per switch
• Speaker: 0.25W, 8Ω, uncommitted
  • Tie Points: 1 x 0.6mm socket for + input; 1 x 0.6mm socket for - input
• BCD to 7 Segment Display: 2 BCD to 7 segment display circuits are provided including decoder/driver circuitry. Tie points: 5 per each unit
• Breadboarding Area: (4) UBS-100 sockets with a total of 3360 uncommitted tie-points, available on velcro breadboard plate. Two QT-59B, bus strips, Fifty tie-points for each +5V variable +V, -V, and ground if desired
• Enclosure: Steel case
• Dimensions: 4.5" (H) x 15" (W) x 10.75" (D)
• Weight: 10 lbs. (4.5kg)
  
  

Features:

• Expanded removable breadboard area included with lifetime warranty
• Two open collector pulsers
• Built-in multi-waveform function generator
• Quad voltage power supply: 3 DC and one low voltage AC
• Functions with optional electronics trainer boards
• Built-in logic probe with pulse capture
• BCD to 7-segment decoder/display
• 8-channel logic indicators

Specifications:

• Power: 3-wire AC line input (115V/230V 50-60Hz ro 230V 50Hz)--(specify when ordering) with power indicator
• Power Supplies:
  • +5VDC @ 1.0A, ripple <5mV