Sensitivity: 5mV/div - 5V/div (x1 mode)
1mV/div - 1V/div (6MHz, -3dB) (x5 mode)
Attenuator: 1-2-5 sequence, 10 step attenuator, plus vernier control
Rise Time: About 8.8ns
Over Shoot: Less than 5%
Input Impedance: 1Mohm +/- 2%, 25pF
+/-10pF
Max. Input Voltage: 400V (DC + AC peak)
Operating Modes: CH 1,CH 2, DUAL (ALT or CHOP) nd ADD
Algebraic Addition: Approximately 500kHz
Inverter: CH 2 only
Horizontal Amplifier
X-Y Mode: Switch selectable using X-Y switch
- CH 1: X axis
- CH 2: Y axis
Accuracy: Y axis +/- 3%, X axis +/-6% |
Bandwidth: DC - 1MHz (-3dB)
X-Y Phase Difference: Approximately 3 deg. at 50kHz
Sweep System
Sweep Display Mode: Main, Mix, Delay
(S-1345 only)
Hold Off Time: 5:1 continuously variable (0.1µs/div)
Main Sweep
Sweep Speed: 0.1µs/div - 0.2s/div in 1-2-5 sequence, 23 steps
Accuracy: +/-3%
Variable Time Control: 5:1, uncalibrated, continuously variable between steps
Sweep Magnification: 10X, +/-10%, extend sweep speed up to 10ns/div
Delayed Sweep (S-1330 only)
Sweep Speed: 0.1µs/div - 0.2s/div in 1-2-5 seq., 23 steps |
Accuracy: +/- 3%
Sweep Magnification: 10X, +/- 10%, extend sweep speed up to 10ns/div
Delay Time Position: Variable control to locate desirable waveform for extending
Trigger
Trigger Coupling: AUTO, NORM,
TV-V, TV-H
Trigger Source: CH 1, CH 2, ALT, LINE, EXT
Slope: +/-
Trigger Sensitivity
| Coupling |
Bandwidth |
Internal |
External |
| TV-V |
DC - 1kHz |
1.0 div |
0.1Vpp |
| TV-H |
1kHz-100kHz |
1.0 div |
0.1Vpp |
| AUTO |
100Hz-40MHz |
1.5 div |
0.1Vpp |
| NORM |
100Hz-40MHz |
1.5 div |
0.1Vpp |
|
Test Voltage: Max. 6Vrrms (open circuit)
Test Current: Max. 11mA (shorted)
Test Frequency: Line Frequency
Components: Capacitor, Inductor, Diode, Transistor, Zener, etc.
CH 2 Output (S-1330 only)
Output Level: 100mV/div (no load), 50mV/div (50ohm load)
Bandwidth: 20Hz - 15MHz (-3dB)
Other Specifications
CRT Type
Rectangular with internal graticule. Adjustable gratiule illumination (S-1345 only)
Display Area: 8 x 10 div (1 div = 1cm)
Accelerating Voltage: 2.1kB, 12kV (S-1345)
Phosphor: P31 Z Modulation (S-1330 only): Positive TTL signal low level blank intensity at any intensity
Trace Rotation: Electrical, adjustable front panel
Calibrator: Square wave: 1kHz +/-10%, 2Vpp +/-3%
Power Requirements: 115, 230 Vac +/-10%, 50/80Hz
Power Consumption: Approximately 40W
Dimensions: 5-1/4" (H) x 12-3/4" (W) x 15-5/8" (D)
Net Weight: 17 lbs. 3.2 oz. (7.8kgs)
Accessories Supplied: Two x1, x10 probes, schematic diagram and parts list, AC power cord, spare fuse, and dust cover |
